Router1#Send *
To Send A Private Message To A User Logged Onto A Specific Line, Use The Send Command With The Line Number:
Router1#Send 66
To Send A Private Message To A User On The AUX Port, Use The Following Command:
Router1#Send Aux 0
To Send A Private Message To A User On The Console Port, Use The Following Command:
Router1#Send Console 0
To Send A Private Message To A User On A Specific VTY Port, Use The Following Command:
Router1#Send Vty 2
Discussion : Sending Messages To Other Users On A Router Is Quite Useful. You Might Want To Use It To Warn Other Users That You Are About To Reload Or Make Changes To The Router. This Is A Particularly Valuable Feature When Remote Users Are Located In Different Geographical Areas. You Can Exchange Messages With Other Users Immediately Without Having To Track Down Individuals Via Phone, Pager, Or Cell Phone.
We Often Use This Feature While Troubleshooting Network Problems. It Is Particularly Useful For Communicating With An On-Site Technician Connected To The Router's Console, Especially If You Have No Other Means To Reach Them. When There Is No Telephone Near The Router, And Cell Phones Won't Work In An Electrically Noisy Equipment Room, This Is A Great Way To Coordinate Everybody's Efforts.
To View All Of The Active Users On The Router, Use The Show Users EXEC Command:
Router1#Show Users
Line User Host(S) Idle Location
66 Vty 0 Ijbrown Idle 01:08:46 Freebsd.Oreilly.Com
<67 Vty 1 Kdooley Idle 00:05:34 Freebsd.Oreilly.Com
* 68 Vty 2 Weak Idle 00:00:00 Freebsd.Oreilly.Com
Interface User Mode Idle Peer Address
Router1#
In The Next Example, We Send A Message To User Kdooley Who Is Connected To VTY1:
Router1#Send Vty 1
Enter Message, End With CTRL/Z; Abort With CTRL/C:
Kev,
I Need To Reload This Router To Clear A Fragmented Memory Problem. Please Save Your Work And Log Off, ASAP... Thanks
Prem.
^Z
Send Message? [Confirm]
Router1#
Notice That Once You Submit The Send Command, The Router Enters A Text Editor Mode. At This Point, You Can Enter Any Free-Form Text. To Exit The Text Editor Mode, Type Control-Z. The Router Then Prompts You For A Confirmation, And If You Confirm, Sends The Message.
An Incoming Message Looks Like The Following:
Router1#
***
***
*** Message From Tty68 To Tty67:
***
Pr,
I Need To Reload This Router To Clear A Fragmented Memory Problem. Please Save Your Work And Log Off, ASAP... Prem.
Router1#
CONCLUSION:
The Goal Of This Article Is To Give An Easy Way To Understand The “CISCO – SENDING MSG TO OTHER USERS". Hope This Article Will Help Every Beginners Who Are Going To Start Cisco Lab Practice Without Any Doubts.
Some Topics That You Might Want To Pursue On Your Own That We Did Not Cover In This Article Are Listed Here, Thank You And Best Of Luck.
This Article Written Author By: Premakumar Thevathasan. CCNA, CCNP, CCIP, MCSE, MCSA, MCSA - MSG, CIW Security Analyst, CompTIA Certified A+.
DISCLAIMER:
This Document Carries No Explicit Or Implied Warranty. Nor Is There Any Guarantee That The Information Contained In This Document Is Accurate. Every Effort Has Been Made To Make All Articles As Complete And As Accurate As Possible.
It Is Offered In The Hopes Of Helping Others, But You Use It At Your Own Risk. The Author Will Not Be Liable For Any Special, Incidental, Consequential Or Indirect Any Damages Due To Loss Of Data Or Any Other Reason That Occur As A Result Of Using This Document. But No Warranty Or Fitness Is Implied. The Information Provided Is On An "As Is" Basic. All Use Is Completely At Your Own Risk.
For Home Page Of - > SCN InF4 TECH
To Send Email
Window Minimize OR Window Maximize
No comments:
Post a Comment